Understanding grain refining and anti Si-poisoning effect in Al-10Si/Al-5Nb-B system

Grain refinement is critical for fabricating high-quality Al-Si casting components in the application of automobile and aerospace industries,while the well-known Si-poisoning effect makes it difficult.Nbbased refiners offer an effective method to refine Al-Si casting alloys,but their anti Si-poisoning capability is far from being understood.In this work,the grain refining mechanism and the anti Si-poisoning effect in the Al-10 Si/Al-5 Nb-B system were systematically investigated by combining transmission electron microscope,first-principles calculations,and thermodynamic calculations.It is revealed that NbB₂provides the main nucleation site in the Al-10 Si ingot inoculated by 0.1 wt.%Nb Al-5 Nb-B refiner.The exposed Nb atoms on the(0001)NbB₂and(1-100)NbB₂surface can be substituted by Al to form(Al,Nb)B₂intermedia layers.In addition,a layer of NbAl₃-like compound(NbAl₃')can cover the surface of NbB₂with the orientation relation of(1-100)[11-20]NbB_2//(110)[110]NbAl₃'.Both of the(Al,Nb)B₂and NbAl₃'intermedia layers contribute to enhancing the nucleation potency of NbB₂particles.These discoveries provide fundamental insight to the grain refining mechanism of the Nb-B based refiners for Al-Si casting alloys and are expected to guide the future development of stronger refiners for Al-Si casting alloys.     

One step method of structure engineering porous graphitic carbon nitride for efficient visible-light photocatalytic reduction of Cr(Ⅵ)

Porous g-C3N4 nanosheets (PCN) were prepared by the nickel-assisted one-step thermal polymerization method.Hydrogen (H2) which was produced by the reaction between nickel (Ni) foam and ammonia (NH3) defined the structure and properties of PCN.During the formation of PCN,the participation of H2 not only enhanced the spacing between layers but also boosted the specific surface area that more active sites were exposed.Additionally,H2 promoted pores formation in the nanosheets,which was beneficial to the transfer of photons through lamellar structure and improved the absorption efficiency of visible light.Remarkably,the obtained PCN possessed better Cr(Ⅵ) photocatalytic reduction efficiency than pure g-C3N4.The reaction rate constant (k) of PCN (0.013 min-1) was approximately twice that of bare g-C3N4 (0.007 min-1).Furthermore,the effects of original pH and concentration of Cr(Ⅵ)-containing solution on removal efficiency of Cr(Ⅵ) were explored.A possible photocatalytic mechanism was proposed based on the experiments of radical scavengers and photoelectrochemical characterizations.     

LNG接收站火炬放空系统设计工况研究与分析

在液化天然气(LNG)接收站工程设计建设过程中，火炬系统的设计是保证LNG接收站安全生产的必要条件。以国内某LNG接收站为例，分析了LNG蒸发气(BOG)产生的因素和机理，及6种工况组合下火炬排放量的计算方法。结果表明：在工况1条件下与实际生产情况吻合良好，其对应的火炬气排放量约为142.7 t/h。在此基础上确定了：BOG支管管径为DN600,BOG总管的管径为DN900;被分离液滴的直径不大于600μm;火炬分液罐尺寸为?2.5 m×8.0 m;电加热器的功率为195 kW;火炬形式为封闭式地面火炬。研究结果可为今后LNG接收站项目火炬系统的处理能力及设备配置提供理论指导。     

Synthesis of nanopowders with low agglomeration by elaborating Φ values for producing Gd2O3-MgO nanocomposites with extremely fine grain sizes and high mid-infrared transparency

Refining ceramic microstructures to the nanometric range to minimize light scattering provides an interesting methodology for developing novel optical ceramic materials. In this work, we reported the fabrication and properties of a new nanocomposite optical ceramic of Gd₂O₃-MgO. The citric acid sol-gel combustion method was adopted to fabricate Gd₂O₃-MgO nanocomposites with fine-grain sizes, dense microstructures and homogeneous phase domains. Nanopowders with low agglomeration and improved sinterability can be obtained by elaborating Φ values. Further refining of the microstructure of the nanocomposites was achieved by elaborating the hot-pressing conditions. The sample sintered at 65 MPa and 1300 °C showed a quite high hardness value of 14.3 ± 0.2 GPa, a high transmittance of 80.3 %–84.7 % over the 3?6 μm wavelength range, due mainly to its extremely fine-grain size of Gd₂O₃ and MgO (93 and 78 nm, respectively) and high density.     

吉林油田低注入井吸水剖面施工工艺控制

本文对吉林油田低注入井五参数测井过程中遇到的一些问题进行分析,并相应提出一系列行之有效的解决方法。     

SND生物脱氮过程N_2O的产生与关键酶及其活性

废水生物脱氮是目前水处理中重要的去除含氮废水的方法。随着国内外学者的深入研究,一些新型的生物脱氮工艺被开发和应用到污水处理中,从而经济高效地去除废水中的含氮污染物,达到国家的排放标准。同步硝化反硝化(SND)是具有发展潜力的新型脱氮工艺,但在运行过程中不可避免地会产生N2O。N2O是最重要的三种温室气体之一,其温室效应约为CO2的300倍。因此,在注重SND的脱氮效率的同时,也应该关注其产生的气态物对大气环境的影响。文章阐述了SND脱氮过程中N2O产生的机理及相关酶,并分析了SND工艺过程中主要影响N2O释放量的工艺因素。     

工业园区混合能源优化配置方法应用与实践

为了充分挖掘多能源之间的互补潜力,使工业园区混合能源系统的配置方式由传统粗放式转变为精确优化配置并降低系统配置方案的保守性,基于粒子群联合CPLEX求解算法对工业园区的系统配置和运行调度方案进行分析优化,并以某生物园区为例进行了实例分析,得到了目标函数下的最优设计方案和运行策略。仿真分析结果表明,优化配置方法的应用能够协调冷热电多种能源的混合利用,提升系统的综合经济性。同时,为工业园区能源供应项目的规划、设计提供参考性支撑,丰富设计手段。